5139

Get a Live Demo

You need to see DPS gear in action. Get a live demo with our engineers.

White Paper Series

Check out our White Paper Series!

A complete library of helpful advice and survival guides for every aspect of system monitoring and control.

DPS is here to help.

1-800-693-0351

Have a specific question? Ask our team of expert engineers and get a specific answer!

Learn the Easy Way

Sign up for the next DPS Factory Training!

DPS Factory Training

Whether you're new to our equipment or you've used it for years, DPS factory training is the best way to get more from your monitoring.

Reserve Your Seat Today

Communications Interface Adapters Bridge Equipment

Communications interface adapters and media converters provide a flexible, cost-effective way to integrate diverse equipment into your network.

Alternate Path Switch

The Alternate Path Switch (APS) is an interface adapter that provides an automatic backup dial-up connection to any remote. The APS connects your T/Mon LNX to any serial remote, providing a primary serial connection. If the primary connection fails, the dial-up connection immediately comes on line for uninterrupted polling.


232-485B Polling Interface

The 232-485B Polling Interface interfaces a two-wire RS-232 data port to a switched-carrier RS-485B data port.


RS-232 to FSK Converter

The RS-232 to FSK Converter interfaces an RS-232 data port to a frequency shift keyed (FSK) modem network in the 4 to 8 kHz frequency band. While the RS-232 to FSK Network Converter can be used for any general application that requires data conversion to FSK, it is specifically intended for T/Mon LNX to access alarm data via an FSK equipment.


8 Channel ASCII MUX

The 8-Channel ASCII MUX allows you to connect up to eight ASCII data sources to one ASCII port on a T/Mon LNX master. The master controls the MUX to route data to the appropriate port. Each channel has a 16K buffer that allows data to be moved between ports at different data rates. In addition to switching between multiple ports, the 8 Channel ASCII MUX will select a preset data rate for each port. Available data rates are 300, 1200, 2400 and 9600 Baud


TL1 MUX-8

The TL1 MUX is a specialized data multiplexer for combining up to 8 data lines using BellcoreTM Transaction Language 1 (TL1) onto a single TL1 line. By observing the delineating semicolon at the end of each TL1 data packet, the processor in the TL1 MUX-8 is able to store and stack incoming data. The TL1 packets are then sent to the common port in the order received and transmitted to the interrogator one-at-a-time.


8 Port Serial Switch

The 8 Port Serial Switch (SPS8) allows you to connect up to eight data sources to one port on a collection device , such as the NetDog 82IP. Commands from an interrogating ASCII terminal control the switch to route data to the appropriate port. Each channel has a 16K buffer that allows data to be moved between ports at different data rates. In addition to switching between multiple ports, the 8 Port Serial Switch will select a preset data rate for each port. Available data rates are 300, 1200, 2400 and 9600 Baud.


FSK Converter

The DPS Telecom FSK Converter interfaces an RS-232 data port to a Frequency Shift Keyed (FSK) modem network. The modem operates at 1200 baud with a center frequency of 1877 Hz.

The FSK Converter with Firmware Version 1.0B is designed to support only one application: mediating alarm data between the T/Mon LNX and the Larse LarScan Series 1200 or Badger 1200 remote telemetry unit. Each FSK System Converter mediates a polling leg of up to 253 Larse/Badger remotes.

Note: This device provides a hardware interface to your Larse/Badger network. To poll the network with a T/Mon LNX, the Larse Interrogator software module (Part number D-SW-LARSE-12001) must be installed on your T/Mon system.


12-Port Router RS232, Craft Port 232

Functional hubs up to 11 RS232 ports to a single RS232 output. Rack mountable 19/23", single rack unit high, available in both wire-wrap and DB9 connections.

The 12-Port Router (8-RS232, 4-Empty Pads), Wire Wrap connects two systems together in a primary/backup configurations and routes the active system (I.e.: 1 four port intelligent ctr). Requires 4 docking modules. Includes RS485 Ctrl & RS232 Craft port. Rack Mountable 19/23".


Protection Switch (8-RS232, 4-Empty pads), RJ11 Connections

(T/Mon Protection Switch) Connects two T/Mon's together in a primary/backup configuration and routes the active system to the peripherals. Routes 4 ports per system (I.e. 1 four port intelligent ctrl). Requires 4 docking modules. Includes RS485 Ctrl & RS232 Craft Port and cable kit. Rack-Mountable 19/23".